Iceriver AE0 60MH/s Aleo Miner

Iceriver AE0 Key Features

The Iceriver AE0 combines low power consumption, compact dimensions and wired network connectivity in a dedicated Aleo mining device.

• Manufacturer: IceRiver
• Model: AE0
• Product name: Iceriver AE0
• Function: Aleo miner
• Rated performance: 60MH/s ±5%
• Rated wall power: 100W ±10%
• Calculated efficiency: Approximately 1.67J/MH
• Network connection: Ethernet
• Direct DC input: 19–20V DC
• AC input with compatible PSU: 100–240V AC
• Official compatible PSU: IceRiver 120W PSU
• PSU included: No, according to the official product listing
• Dimensions: 200 × 194 × 74mm
• Net weight: Approximately 2.5kg
• Operating temperature: 0°C to 40°C
• Cooling method: Compact air cooling
• Primary network: Aleo
• Recommended use: Home, hobby and small-scale mining

Iceriver AE0 Specifications

Specification note: IceRiver officially lists the Iceriver AE0 at 60MH/s ±5% and 100W ±10%. The official dimensions are 200 × 194 × 74mm, not 198 × 201 × 110mm.

Noise was removed from the primary specification table because IceRiver’s official product page does not publish a verified decibel rating for this model.

Iceriver AE0 Aleo Mining Performance

The Iceriver AE0 delivers approximately 60MH/s of Aleo-compatible processing under normal operating conditions. The manufacturer publishes a ±5% performance tolerance, so local readings may move slightly above or below the nominal value.

Actual accepted performance may also vary because of:

• Network and pool conditions
• Firmware version
• Ethernet stability
• Pool latency
• Room temperature
• Cooling performance
• Power-supply quality
• Production tolerance
• Miner uptime

Operators should compare the local Iceriver AE0 dashboard with accepted pool-side statistics over several hours. Temporary peaks or drops should not be treated as permanent performance.

Important Monitoring Values

• Local performance reading
• Average accepted pool performance
• Accepted shares or proofs
• Rejected submissions
• Ethernet uptime
• Pool latency
• Device temperature
• Fan operation
• Measured wall power
• Continuous uptime

Iceriver AE0 Power Efficiency

The calculated efficiency of the Iceriver AE0 is:

100W ÷ 60MH/s = approximately 1.67J/MH

This figure represents the nominal electrical power used for each megahash of rated Aleo processing performance.

Efficiency should not be confused with profitability. Mining returns also depend on:

• Aleo market value
• Network reward structure
• Network competition
• Pool fees
• Electricity cost
• Hardware price
• PSU cost
• Shipping charges
• Miner uptime

Iceriver AE0 Electricity Consumption

At a continuous nominal load of 100W, estimated electricity consumption is:

• 2.4kWh per day
• 16.8kWh per week
• 72kWh per 30-day month
• 876kWh per year

Estimated monthly electricity costs are:

• At $0.05/kWh: approximately $3.60
• At $0.08/kWh: approximately $5.76
• At $0.10/kWh: approximately $7.20
• At $0.15/kWh: approximately $10.80
• At $0.20/kWh: approximately $14.40
• At $0.30/kWh: approximately $21.60
• At $0.40/kWh: approximately $28.80

Because the official rating includes a ±10% power tolerance, actual electricity consumption may be slightly higher or lower.

A wall power meter should be used to measure the combined consumption of the Iceriver AE0 and its external PSU.

Iceriver AE0 and Aleo Mining

The Iceriver AE0 is purpose-built for Aleo-compatible proof generation. Aleo is a privacy-focused blockchain platform that uses zero-knowledge technology to support private applications and transactions.

The term “zkSNARK miner” is frequently used in reseller listings, but zero-knowledge proofs are broader cryptographic tools rather than a simple mining algorithm comparable to SHA-256 or Scrypt.

For clearer product wording, the Iceriver AE0 should be described as:

• An Aleo miner
• An Aleo proof-generation device
• A dedicated Aleo mining machine
• A specialized Aleo-compatible processing unit

Learn more through the official Aleo website and review official product details on the IceRiver AE0 product page.

Iceriver AE0 Pool Configuration

The Iceriver AE0 connects to compatible Aleo mining or proving services through wired Ethernet.

Configuration may require:

• A compatible Aleo server or pool address
• An Aleo wallet or pool account
• A worker name
• A worker password
• Secondary and tertiary backup servers

Pool Selection Checklist

• Explicit AE0 support
• Aleo network compatibility
• Payment method
• Pool or service fee
• Minimum payout threshold
• Regional server availability
• Historical uptime
• Worker-monitoring features
• Support responsiveness

After configuring the Iceriver AE0, confirm that the pool or service dashboard shows accepted work and a performance level reasonably close to the expected output.

Iceriver AE0 Power-Supply Requirements

The Iceriver AE0 requires approximately 19–20V DC input. IceRiver’s official 120W PSU provides 19V DC output and supports 100–240V AC input at 50–60Hz.

The official PSU is rated for:

• Input voltage: 100–240V AC
• Input frequency: 50–60Hz
• Output voltage: 19V DC
• Maximum output power: 120W
• Maximum output current: 6.32A
• Output connector: DC 5.5 × 2.5mm

At the miner’s nominal 100W demand, approximate AC current is:

• Approximately 1A at 100V
• Approximately 0.83A at 120V
• Approximately 0.45A at 220V
• Approximately 0.42A at 240V

Actual current will be slightly higher because of PSU conversion losses.

Do not connect the Iceriver AE0 directly to AC power without a compatible power supply.

Iceriver AE0 Cooling and Placement

The Iceriver AE0 produces approximately 100W of continuous heat. This is substantially lower than the heat generated by industrial mining hardware, but airflow is still required.

Placement Recommendations

• Keep the ventilation openings clear.
• Place the miner on a stable surface.
• Do not cover the chassis.
• Avoid sealed drawers or cabinets.
• Keep the miner away from direct sunlight.
• Keep the PSU ventilated.
• Avoid moisture and condensation.
• Remove dust periodically.
• Keep liquids away from the device.
• Maintain an ambient temperature between 0°C and 40°C.

The miner may be more home-friendly than a large ASIC, but it should not be described as silent unless a verified sound measurement is available.

Iceriver AE0 Installation Guide

1. Inspect the miner and package for shipping damage.
2. Confirm that the factory label states AE0.
3. Verify the 60MH/s and 100W ratings.
4. Obtain a compatible 19–20V DC power supply.
5. Place the miner in a ventilated location.
6. Connect the Ethernet cable.
7. Connect the PSU to the miner.
8. Connect the PSU to a suitable AC outlet.
9. Power on the miner.
10. Locate the device’s IP address through the router or IceRiver utility.
11. Open the web-based management interface.
12. Change default credentials where supported.
13. Enter the primary compatible Aleo pool or server address.
14. Add the wallet or account information.
15. Configure backup servers.
16. Save the settings.
17. Wait for accepted work to appear.
18. Monitor performance, temperature and network stability.

During initial operation, monitor the Iceriver AE0 for connection failures, unusual fan noise, high temperatures, repeated restarts and an overheating power adapter.

Iceriver AE0 Maintenance

Routine maintenance helps the Iceriver AE0 maintain stable temperatures, network connectivity and accepted performance.

• Inspect ventilation openings.
• Remove accumulated dust carefully.
• Monitor miner temperature.
• Check PSU temperature.
• Inspect the DC connector.
• Check Ethernet cables and router stability.
• Compare local and pool-side performance.
• Review rejected work.
• Back up configuration before firmware updates.
• Use only firmware intended for the AE0.
• Disconnect power before cleaning.

IceRiver warns users to apply only model-specific firmware and to download firmware from its official website. Installing incompatible firmware can damage the miner and affect warranty coverage.

Official updates are available through the IceRiver firmware page.

Iceriver AE0 Buying Considerations

Before purchasing an Iceriver AE0, compare the total delivered cost rather than focusing only on the advertised miner price.

Check Before Ordering

• Exact AE0 model label
• 60MH/s performance rating
• 100W power specification
• New, used or refurbished condition
• PSU inclusion
• Correct 19–20V DC output
• Ethernet cable requirements
• Current firmware version
• Seller warranty
• Return policy
• Shipping insurance
• Import duties and taxes
• Current Aleo pool compatibility

IceRiver’s official listing states that the PSU is not included. Confirm whether your reseller package includes a compatible adapter before placing the order.

Contact Hash Titans to check current availability, package contents, shipping details and purchase support for the Iceriver AE0.

Iceriver AE0 Warranty and Shipping

Warranty coverage for the Iceriver AE0 depends on the purchase channel, seller terms and IceRiver’s applicable warranty policy.

• Confirm whether the miner is in stock or preorder.
• Verify the warehouse location.
• Check whether the PSU is included.
• Confirm the expected dispatch period.
• Review shipping-insurance coverage.
• Check customs duties and import taxes.
• Ask who handles warranty claims.
• Inspect the package immediately after delivery.
• Photograph any transport damage before installation.

The official product page may display a current or historical price, but the actual delivered cost can change because of availability, shipping, taxes and reseller margins.

Iceriver AE0 Frequently Asked Questions